Showing posts with label small detail. Show all posts
Showing posts with label small detail. Show all posts

Monday, 2 March 2026

Baguley Frame Details Fitted

Having removed the unwanted parts on both frame ends on the Baguley-Drewry loco, it was time to add the first new parts on the loco. As planned I added new couplings/buffers and as an 'extra thing' I also decided to add sanding gear on the centre axle wheels despite it being very hard to see from normal viewing angles.

New buffers are now fitted to Nystrup Gravel's Baguley-Drewry. The buffers were probably made in Nystrup Gravel's own workshop after images of the type usually being fitted to Nagbøl locomotives.

To make a coupling that is fastened well in the frame ends I decided to use the bolts that held the original coupling pockets on the Accucraft model. As usual I cut a cardboard piece to test size and aid in design. I made the real plasticard version a little deeper and added the 'ribs' that enable the coupling chain to be fitted at alternating heights fitting wagons with different frame/coupling heights.

As usual I test design and size with a piece of cardboard before I begin the real work on new parts. 

Finished slightly deeper than the cardboard version, the front buffer is beginning to materialize. I use the bolts from the original coupling to fasten the new buffer.

Once the main construction of the buffers was finished I sanded the corners round and added boltheads in the lower corners from hexagonal plastic strip. Then I drilled a central hole through the buffer to enable a rod to fasten the coupling chain in the coupling/buffer.

The 'ribs' that enables coupling to wagons for varying height are being added. The plasticard jig giving equal distance between the 'ribs' are seen in the foreground.


Steel skips coupled to the Baguley-Drewry's new buffer. 

The pipes for sanding the centre pair of driving wheels (in both directions) were made from simple lengths of metal wire soldered to a bracket cut from scrap etched metal. Each bracket screws into the loco frame underside with two of the screws that held the now removed power pick-ups. 

Sanding pipes fitted to the centre wheel set. In the image they still need to be finely adjusted to a close fit but still allowing the wheel to rotate freely.

A viewer will have to look carefully for the sanding pipes to discover them. They may show more clearly after painting, but even in 1/1 scale sanding pipes aren't the most noticable feature on locomotives.

I'm also exploring how to fit an on/off switch next to the battery and a cardboard test bracket has been mounted on the underside of the frame. If I decide to use this solution I will probably have to adjust the height of the slide switch to avoid it snagging on track parts and vegetation. I still haven't made up my mind completely.

Testing shape and placement of a bracket for an on/off switch. As usual with a cheap prototype test part made from cardboard.

The work on the Baguley-Drewry loco will continue and there is a long list of tasks awaiting me. I will probably be focusing on installing the Loco Remote unit as one of the first tasks, as that will give me a good base to work on: underframe detailed and a running locomotive with 'only' work on the upper body remaining.

Tuesday, 16 December 2025

Ladas in H0

With a steady stream of Eastern European railway models in 1/87 scale arriving, I have begun collecting a few matching cars as well. I had no problem selecting the first type of car to buy: Lada. Rugged, practical, and iconic, it symbolised (well, kind of) national pride in the Soviet Union and will continue to outlive the USSR for many more years.

The Busch Lada 1200 loaded on a Soviet narrow gauge flat wagon. Not an unlikely load in a post-Soviet rural area even today.

There is a wide range of Lada models available but I chose two of the models from the Busch range. I decided to have a rather early model and one of the more recent that I remember myself - including a taxi ride in one on some very frozen streets of Leningrad.

The 1971 Lada 1200 is a finished model while the 1976 Lada 1600 is in kit form.

Instructions for the assembly of the Lada 1600. I think I can handle this level of complexity...

The Lada 1200 (VAZ-2101 'Zhiguli') was a licence-built version of the Italian Fiat 124, that was heavily modified and tailored for the rough climate and road conditions across the Soviet Union.  The car was widely and successfully exported to the West under the Lada brand for more than two decades.

The Lada 1600 (VAZ-2106 'Zhiguli') was a modernised version of the original model and it became the Soviet contribution to top the Eastern Bloc charts for comfort and prestige during the communist period as the really expensive and luxurious GAZ and ZIL cars, intended for party members and various state officials, were completely out of reach for ordinary people. 

The Lada 1600 was in production 1976–2006 and after the fall and disintegration of the Soviet Union the model was produced by Russian IzhmashAvto in Izhevsk and RosLada in Syzran. There seems to have been a 'shadow production' in Ukraine, but it was most likely nothing but a tax evading assembly of parts imported from Russia.

I'm slowly beginning to settle for a 2000-themed Eastern European in the western, rural part of the area. Consequently the Ladas will be rather old cars and heavily weathered.

Thursday, 5 December 2024

Embedding Petrol Pump

As part of the work giving the Nystrup Gravel layout a more prototypical surface, I have been working on the area around the petrol pump. I wanted the petrol pump to be removable, still not having its looks spoiled by gaps between ground and pump foundation. Not an easy task to accomplish.

In this view the Nystrup Gravel petrol pump towers above the flat meadows to the north of the tracks.

The pump is a cheap chinese toy model I bought back in 2019. I have been refining it a bit but am still looking for a finer detailed pump. By having the pump able to be lifted off the layout it is easily replaceable. When moving the layout, the risk of damaging structures and details is also much smaller when they can be lifted off separately. 

My initial plan was to mount a bolt in the pump and attach it through the layout with a nut from the underside. A bit over the top for an item that won't just fly off at the slightest touch and I settled for a simple piece of brass rod fitting tightly into a brass pipe glued into the foam baseboard.

Before scattering ground cover material around the pump's foundation I wrapped the pump in plastic cling wrap. The thin plastic material creates a good barrier between foundation and the mix of glue and sand for ground cover. Once the glue has dried, the petrol pump was carefully lifted off, the wrap removed and the pump fitted again. A few tufts of grass helped to blend the foundation into the ground.

A brass pipe buried in the layout surface to accept the brass part added to the petrol pump.


Brass rod fitted for keeping the pump in place on the layout.


Diluted white glue has been added to the sand/gravel mix around the petrol pump. The cling wrap prevents the white glue from cementing sand and pump solidly together.

From the front of the layout there is hardly any gaps to be seen even if the petrol pump is removable.